Product Carousel Tabs
Speedzone 9.5 Brushless Motor
Features:
– Adjustable timing
– High RPM precision bearings
– High Temp high purity copper stator wire
– Super Flow power solder tabs
– CNC-machined Billet T6 aluminum can
– Powered sintered neodymium magnet
– Maximized Airflow
– Fully rebuild-able
– Lightweight design and components
– Low Resistance Stator
– Strict Tolerance Sensor Board
– Meets ROAR, IFMAR and EFRA specs
ROAR Approved
Speedzone 6000mAh 120C 2S 7.4V LCG Graphene Lipo – Peerless Series
LCG Lipo Pack rated at continuous 120C. Standard 5mm connectors.
The low-profile design allows you to further fine tune the handling characteristics of your car.
– High capacity for maximum duration
– 120C discharge rating
– Low Resistance
– High AV
– Low Profile
– 5mm connectors
– Dimensions: 139mm(L)x47mm(W)x22.4mm(H)
– Weight: 292g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Speedzone 17.5 Brushless Motor
Features:
– Adjustable timing
– High RPM precision bearings
– High Temp high purity copper stator wire
– Super Flow power solder tabs
– CNC-machined Billet T6 aluminum can
– Powered sintered neodymium magnet
– Maximized Airflow
– Fully rebuild-able
– Lightweight design and components
– Low Resistance Stator
– Strict Tolerance Sensor Board
– Meets ROAR, IFMAR and EFRA specs
Available in “Standard”, “Select” and “Tuned” versions.
ROAR and BRCA Approved
Evolution SC80 80A SPEC ESC
The SC80 electronic speed controller (ESC) is specifically designed for 1/10 scale SPEC class electric R/C racing and is suitable for both off-road and on-road classes. It comes factory set in “blinky” mode with the same setup of United States Stock TC ACE Dave Johnson. And although the factory default setting is an optimized setup for “blinky” mode, an optional program box is available to customize settings to suite driving styles in “blinky” mode as well as non-“blinky” mode. The controller is 2S LiPo compatible, has a 9.5T and above motor limit and comes with factory installed wires, capacitor and fan.
Specifications:
Continuous Current: 80A
Battery Input: 2S LiPo, 2S LiFe, 4-8 cells NiMh/NiCd
Built-in BEC: 6V@5A
Motor Limit: Over 9.5T
Motor Type: 540 size 2 pole sensored brushless
Size: 32mm(L) x 26mm(W) x 24mm(H – with fan)
Weight: 52g (with fan, wires and capacitor)
Evolution 5500mAh 130C 2S 7.4V Slim Lipo
Slim Pack rated at continuous 130C. Standard 5mm connectors.
The slim design allows you to further fine tune the handling characteristics of your car.
– 130C discharge rating
– Low Resistance
– High AV
– Slim Design
– 5mm connectors
– Dimensions: 139mm(L)x37.3mm(W)x24.8mm(H)
– Weight: 238g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Speedzone 8000mAh 7.4V 100C Graphene Lipo – Peerless Series
This is the latest release to the Speedzone Peerless Series Hardcase Lipo Packs. Rated at continuous 100C and is the highest C rated and mah pack in the Speedzone Lipo Product Line. Standard 5mm connectors.
The Peerless Series offers higher C rated packs with lower internal resistance and more stringent tolerance levels.
Dimensions: 139mmx46.5mmx25mm
Speedzone 8000mAh 7.4V 120C Graphene Lipo – Peerless Series
This is the latest release to the Speedzone Peerless Series Hardcase Lipo Packs. Rated at continuous 120C and is the highest C rated and mah pack in the Speedzone Lipo Product Line. Standard 5mm connectors.
The Peerless Series offers higher C rated packs with lower internal resistance and more stringent tolerance levels.
Dimensions: 139mmx46.5mmx25mm
Weight: 328g
Speedzone 4000mAh 100C 2S 7.4V Shorty Slim LCG Graphene Lipo – Peerless Series
Speedzone 4000mAh 100C 2S 7.4V Shorty Slim LCG Graphene Lipo – Peerless Series
SLIM LCG Shorty
Pack Rated at continuous 100C. 5mm connectors.
Ideal for spec class and modified racing. Thin pack at just 18.5mm in height.
– True capacity at 7.4v
– 100C discharge rating
– 5mm connectors
– Weight: 162g +/- 2g
– Dimensions LxWxH: 95.0 x 46.5 x 18.4 mm
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Evolution 5200mAh 130C 2S 7.4V Shorty Lipo
High AV, Low IR. Rated at continuous 130C. Standard 5mm connectors.
– High capacity for maximum duration
– 130C discharge rating
– Low Resistance
– High AV
– 5mm connectors
– Dimensions: 96mm(L)x47mm(W)x25mm(H)
– Weight: 228g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
– ROAR Approved
Motors
Batteries
Evolution 4000mAh 120C 2S 7.4V Shorty Lipo
Shorty Pack Rated at continuous 120C. 5mm connectors.
Ideal for spec class racing. This pack was specially designed to have super high voltage with low internal resistance.
– High Voltage
– Low Internal Resistance
– 120C discharge rating
– 5mm connectors
– Dimensions: 96mm(L)x47mm(W)x25mm(H)
– Weight: 210g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
– ROAR Approved
Speedzone 4300mAh 120C 2S 7.4V Shorty LCG Graphene Lipo – Peerless Series
Speedzone 4300mAh 120C 2S 7.4V Shorty LCG Graphene Lipo – Peerless Series
LOW PROFILE Shorty Pack Rated at continuous 120C. 5mm connectors.
The low-profile design allows you to further fine tune the handling characteristics of your car.
– High capacity for maximum duration
– 120C discharge rating
– 5mm connectors
– Dimensions: 96mm(L)x47mm(W)x22.4mm(H)
– Weight: 194g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Speedzone 5000mAh 120C 2S 7.4V Lipo – Peerless Series
Rated at continuous 120C. Standard 5mm connectors.
The biggest advantage of this pack is the high average voltage and super low resistance, making it perfect for not only spec classes but modified classes as well.
– High capacity for maximum duration
– 120C discharge rating
– Low Resistance
– High AV
– 5mm connectors
– Meets ROAR, EFRA, BRCA, and IFMAR specs
– Weight: 288g
Evolution 5000mAh 120C 2S 7.4V Shorty Lipo
Rated at continuous 120C. 5mm connectors.
– High capacity for maximum duration
– 120C discharge rating
– 5mm connectors
– Dimensions: 96mm(L)x46.5mm(W)x24.5mm(H)
– Weight: 212g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Evolution 6000mAh 120C 1S 3.7V Lipo
This is the best pack for spec class racing.
– Super High Voltage
– Low Internal Resistance
– 120C discharge rating
– Low Resistance
– High AV
– 5mm connectors
– Dimensions: 93mm(L)x47mm(W)x18.5mm(H)
– Weight: 150g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
– ROAR Approved
Speedzone 6000mAh 120C 2S 7.4V LCG Graphene Lipo – Peerless Series
LCG Lipo Pack rated at continuous 120C. Standard 5mm connectors.
The low-profile design allows you to further fine tune the handling characteristics of your car.
– High capacity for maximum duration
– 120C discharge rating
– Low Resistance
– High AV
– Low Profile
– 5mm connectors
– Dimensions: 139mm(L)x47mm(W)x22.4mm(H)
– Weight: 292g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Speedzone 6000mAh 120C 2S 7.4V Graphene Lipo – Peerless Series
This is the latest pack release to the Speedzone Peerless Series Lipo Packs. Rated at continuous 120C. Standard 5mm connectors.
– High capacity for maximum duration
– 120C discharge rating
– Low Resistance
– High AV
– 5mm connectors
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Speedzone 6000mAh 15.2V 100C LIHV Graphene Lipo – Peerless Series
LIHV 100C 4S pack from Speedzone. Rated at continuous 100C. Standard with direct connect Deans connectors.
Dimensions: 138.5mm(L)x46.5mm(W)x49mm(H)
Weight: 556g
This is an LIHV pack. You will need a LIHV charger to take full advantage of the 15.2V. Pack can be charged to 4.35v per cell.
Speedzone 7200mAh Lipo 7.4V 100C – Peerless Series
Rated at continuous 100C. Standard 5mm connectors.
The Peerless Series offers higher C rated packs with lower internal resistance and more stringent tolerance levels.
Comes with bullet connectors with deans plug and standard balance plug!
Dimensions: 139mmx46.5mmx25mm
Speedzone 7500mAh 120C 2S 7.4V Lipo – Peerless Series
This is the latest high capacity pack release to the Speedzone Peerless Series Lipo Packs. Rated at continuous 120C. Standard 5mm connectors.
– High capacity for maximum duration
– 120C discharge rating
– Low Resistance
– High AV
– 5mm connectors
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Speedzone 8000mAh 7.4V 100C Graphene Lipo – Peerless Series
This is the latest release to the Speedzone Peerless Series Hardcase Lipo Packs. Rated at continuous 100C and is the highest C rated and mah pack in the Speedzone Lipo Product Line. Standard 5mm connectors.
The Peerless Series offers higher C rated packs with lower internal resistance and more stringent tolerance levels.
Dimensions: 139mmx46.5mmx25mm
Chargers, Setup & Tuning
iCharger 206B
Specifications:
Input Voltage Range: 10 – 28.0VDC
Charge Current Range: 0.05 – 20.0A
Discharge Current Range: 0.05 – 20.0A
Maximum Charge Power Capacity: 300W @ Input voltage > 18V
Internal Discharge Power Capacity: 20W maximum internal
External Discharge Power Capacity: 500W @ 25V/20A
Current Drain For Balancing: <350mA
Balance Accuracy: <10mV
Lithium (LiPo/LiIo/LiFe) Battery Cell Count: 1 – 6 Series (In non-balance mode, expand LiFe to 8s)
NiCd/NiMH Battery Cell Count: 1 – 17 series
Pb Battery Cell Count: 1 – 12 series (2 – 24V)
Battery Setup Memories: 10
Intelligent Temperature Control: Yes
PC Connect: USB port
Weight: 350g
Dimensions (L X W X D): 134 x 83 x 25mm (5.3" x 3.3" x 1")
iCharger 306B
Input voltage range: 4.50 – 38.0VDC
Charge current range: 0.05 – 30.0A
Discharge current range: 0.05 – 30.0A
Maximum charge power capacity: 1000W @ input voltage 23V (500W @ input voltage 12V)
Maximum discharge power capacity: 80W
Maximum regenerative discharge power capacity: 1000W
Maximum extern discharge power capacity: 1200W @ 40V/30A
Current drain for balancing: <500mA
Balance accuracy: <10mV
Lithium (LiPo/LiIo/LiFe) battery cell count: 1 – 6 series (In non-balance mode, expand LiFe to 12s)
NiCd/NiMH battery cell count: 1 – 25 series
Pb battery cell count: 1 – 18 series (2 – 36V)
Log Files storage: 16Mbit (31 hours)
Battery setup memories: 10
Intelligent temperature control: Yes
PC Connect: USB port
Weight: 750g
Dimensions (L X W X D): 143X123X46mm 5.63”X4.84”X1.81”
iCharger 308DUO
30A 1300W Dual Port Battery Charger Discharger – Eligible for FREE shipping!
308DUO Special Features
1 The 308DUO uses advanced Synchronous buck-boost DC/DC converter technology, high power, a high current and high-performance power conversion circuit. The maximum charge power capacity is up to 1300W, the maximum charge/discharge current of a channel is up to 30A, and two channels in Synchronous Mode are up to 50A.
2 Each channel supports 8s LiPo, Lilo, LiFe and NiZn batteries, with maximum 1.2A balance current, and adopts a unique balance calculation of internal resistance correction. Supports 1-20s NiMH/NiCd batteries and 1-15s Pb batteries..
3 With 1A/5V USB charging port, convenient for the user to charge mobile phones and PCs.
4 When the channel output connects the battery after the charger powers on, it will start automatically the anti-sparking protection.
5 Intelligent fan control. Sensing internal temperature via the internal temperature sensor, to thereby control the fan speed.
6 Internal temperature protection. When the internal temperature exceeds the Power Reduce temperature, the output power is automatically reduced; and the charger will shut down when temperature exceeds the Shut-down temperature.
7 This charger can save 64 parameters sets and supports the data import/export to SD card
8 A 2.8-inch LCD screen provides rich information including current, voltage, power, capacity, internal resistance, control status, time-consuming and temperature, etc.
9 Multi-discharge features: self-discharge, regenerative to input discharge, and lithium battery extra expanding discharge.
10 Supports measurement for internal resistance of battery offline and online. Can measure not only the internal resistance of the entire battery pack, but also measure the internal resistance of each cell within the lithium battery.
11 The iCharger has protection for reversed polarity (input or output), input voltage/current, battery temperature, charging capacity, overrun time and maximum power etc.
12 Supports upgrading the hardware program by USB port or SD card. The iCharger also supports the “Logview” software and can display, plot and analyze the charge and discharge data by it. (See detailed information about Logview at the following website: http://www.logview.info )
iCharger 4010DUO
40A 2000W Dual Port Battery Charger Discharger
4010DUO Special Features
1. The 4010DUO uses advanced Synchronous buck-boost DC/DC converter technology, high power, and high current and high-performance power conversion circuit. The maximum charge power capacity up to 2000W, the maximum charge/discharge current of channel up to 40A, and two channels in Synchronous Mode up to 70A.
2. Channel Supports 10s LiPo, Lilo, LiFe, with maximum 1.2A balance current, adopts unique balance calculation of internal resistance correction .
3. Intelligent fan control. Sensing internal temperature via the internal temperature sensor, to thereby control the fan speed.
4. Internal temperature protection. When the internal temperature exceeds the reduce temperature, the output power is automatically reduced; and the charger will shut down when temperature exceeds the cut-temperature.
5. 64 parameters sets can be saved, without repeat setting when use, just import/export via SD card.
6. TFT LCD screen that provides rich information including current, voltage, power, capacity, internal resistance, control status, time-consuming and temperature, etc.
7. Multi-discharge features: discharge-self, regenerative to input discharge, regenerative to channel discharge, and lithium battery extra expanding discharge.
8. Support measurement for internal resistance of battery offline and online. Can measure not only the internal resistance of the entire battery pack, but also measure the per-cell internal resistance of lithium battery.
9. The iCharger has protection for reversed polarity (input or output), input voltage/current, battery temperature, charging capacity, time overrun and maximum power etc.
10. Supports upgrading the hardware program by USB port. The iCharger also supports the “Logview” software and can display, plot and analyze the charge and discharge data by it. (See detail information about Logview in the following website: http://www.logview.info)
iCharger 406DUO
40A 1400W Dual Port Battery Charger Discharger – Eligible for FREE shipping!
406DUO Special Features
1 The 406DUO uses advanced Synchronous buck-boost DC/DC converter technology, high power, a high current and high-performance power conversion circuit. The maximum charge power capacity is up to 1400W, the maximum charge/discharge current of a channel is up to 40A, and two channels in Synchronous Mode are up to 70A.
2 Each channel supports 6s LiPo, Lilo, LiFe and NiZn batteries, with maximum 1.2A balance current, and adopts a unique balance calculation of internal resistance correction. Supports 1-20s NiMH/NiCd batteries and 1-12s Pb batteries.
3 With 1A/5V USB charging port, convenient for the user to charge mobile phones and PCs.
4 When the channel output connects the battery after the charger powers on, it will start automatically the anti-sparking protection.
5 Intelligent fan control. Sensing internal temperature via the internal temperature sensor, to thereby control the fan speed.
6 Internal temperature protection. When the internal temperature exceeds the Power Reduce temperature, the output power is automatically reduced; and the charger will shut down when temperature exceeds the Shut-down temperature.
7 This charger can save 64 parameters sets and support the data import/export to SD card.
8 A 2.8-inch LCD screen provides rich information including current, voltage, power, capacity, internal resistance, control status, time-consuming and temperature, etc.
9 Multi-discharge features: self-discharge, regenerative to input discharge, and lithium battery extra expanding discharge.
10 Supports measurement for internal resistance of battery offline and online. Can measure not only the internal resistance of the entire battery pack, but also measure the internal resistance of each cell within the lithium battery.
11 The iCharger has protection for reversed polarity (input or output), input voltage/current, battery temperature, charging capacity, overrun time and maximum power etc.
12 Supports upgrading the hardware program by USB port or SD card. The iCharger also supports the “Logview” software and can display, plot and analyze the charge and discharge data by it. (See detailed information about Logview at the following website: http://www.logview.info)
SkyRC Brushless Motor Anaylzer
SKYRC motor analyzer is a precision electronic device that is especially designed for measuring the KV value, RMP, current drawn, motor timing, vibration noise level and checking the function of hall effect sensors of a brushless motor. It comes with a 2X16 characters LCD that is able to display real time measuring value of either sensor or sensor-less brushless motor.
This is the latest version which will go past the 50 deg timing.
SkyRC Corner Weight System
This Corner Weight System is designed for serious racers to measure their cars’ corner weight distribution easily and make necessary weight adjustment to balance their cars for the best performance.
Corner weight scales allow precise car weight distribution which is critical to on track success. The four corners of the car may be bearing different amounts of the car weight. The unequal corner weights can be felt as the car rolling more when turning in one direction than the other. The car’s stability is compromised which will adversely affect its balance. A well balanced car is generally easier to drive quicker due to increased the car’s stability.
To make sure weight percentages are correct, computerized scale system must be used. Correct chassis setup separates the front runners from the followers. Corner Weight Scales provide the necessary data for anyone to become a chassis expert.
Features:
•Designed for 1/8 buggy and truck, 1/10 buggy & touring car and 1/12 cars.
•Measure the car’s corner weight, front and rear distribution and make adjustment if necessary.
•The maximum weight limit for each scale is 2000 grams(total 8000 grams).
•Measurements can be displayed in gram, oz.
•Highly accurate weight measurement in 0.1g increments (equivalent to 0.01 oz).
•4 red LED screens for displaying each corner weight measurement.
•2 green LED screens for displaying front weight and rear weight.
•2 green LED screens for displaying corner weighting(front right + rear left, front left + rear right).
•1 green LED screen shows total weights.
•4 LED screens for displaying percentage of weights distribution. 4 large, easy to clean aluminum weighting surface and easy to use 3 button operation.
•Powered by 4 x AA batteries (batteries NOT included) or external DC source(6-13.8V).
Eligible for FREE shipping!
SkyRC LED Pit Light
Skyrc LED pit light with motion sensor to control the brightness of LED. The LED pit light also featured a fold-able design with an aluminum tray for small parts and screws to keep your pit table clean and organised. This LED pit light can be used with a DC power source.
SkyRC Tire Sander
SkyRC Rubber Tire Sander can be powered by a 12V power supply, as well as powered directly from a 2S LiPo battery! The Tire Sander is a quick and easy way to remove the seam from the center of a new tire, without having to take 2-3 laps around the track.
Features:
• Rubber tire sander for touring class
• Powerful high torque DC motor with dual metal bearings
• Adjustable RPM of motor
• 8 LEDs indicate tire running RPM
• Light-weight aluminum case
• Quiet operation
• Protection: Input reverse polarity protection
• Tire running rotation can be changed
SkyRC Tire Warmer
SKYRC RSTW Tire Warmers are designed to pre-heat rubber tires for 1/10 size touring car.
Features:
• Front & Rear temperature can be set independently
• Temperature of 4 tires is controlled by MCU
• Removable front & rear tire warmers
• 8 different beep tones
• Minimum temperature
• Celsius – Fahrenheit selectable display
• Four LED indicators
• Safety timer
iCharger X6
The highest power density charger on the market, the X6 is an 800W charger capable of a full 30A rate on LiPos up to 6S. With a balance current of a full 2A, charges will finish faster than ever. The full color IPS display provides a wealth of information at a glance, using the operating system perfected on the larger Duo iChargers.
The X6 can charge at up to 30A, and it can also discharge at up to 30A! While similar size chargers limit their discharge capabilities, the X6 offers iCharger’s trademark support for regenerative discharge, allowing the charger to provide a full 800W of discharge capability when powered from a suitable battery bank.
Despite its small size and low price, this is still a full featured iCharger, with multi-chemistry support and all the depth of settings you’ve come to expect, including an improved software interface for recording battery data and upgrading firmware.
Specifications:
Net weight: 168g
Dimension: 83x65x37 ±0.5mm
Input Voltage Range: 10.0—32.0VDC
Maximum Input Current Limit: <35A
Maximum Charge/Discharge Current: 30A
Maximum Charge Power Capacity: 800W
Maximum Discharge Power Capacity: 30W
Maximum Regenerative Discharge Power Capacity: 800W
Maximum Extra Discharge Power Capacity: 900W @30V/30A
Maximum Current Drain for Balancing: >2A
Ultra Power UP120AC DUO
2 Port 12A Battery Charger Balance LiPo LiHV NiMH AC/DC
Ultra Power UP100AC DUO
Compact Charger. Comes with cables and balance boards. US Plug for AC.
Input voltage: AC 100~240V DC 11.0-18.0V
Charge power: Max. 100W (CH1) Max. 50W (CH2)
Discharge power: Max. 10W (CH1) Max. 5W (CH2)
Charge current: Max. 10.0A (CH1) Max. 6.0A (CH2)
Discharge current: Max. 5.0A (CH1) Max. 2.0A (CH2)
LiIon/LiPo/LiFe/Li-Hv: 1~6 series
NiCd/NiMH battery cell count: 1 – 15cells
Pb battery voltage: 2V～20V (1-10cells)
Balance Current: 300mah/cell
Weight: 1.0KG
Dimension: 143X115x63mm
Ultra Power UP240AC Plus
2 Port 12A Battery Charger Balance LiPo LiHV NiMH AC/DC
Recently Added
Evolution 6000mAh 120C 4S 14.8V Lipo
High AV, Low IR. Rated at continuous 120C. Standard 5mm connectors.
– 120C discharge rating
– Low Resistance
– High AV
– 5mm connectors
– Dimensions: 139mm(L)x47mm(W)x48mm(H)
– Weight: 534g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Evolution 5500mAh 130C 2S 7.4V Slim Lipo
Slim Pack rated at continuous 130C. Standard 5mm connectors.
The slim design allows you to further fine tune the handling characteristics of your car.
– 130C discharge rating
– Low Resistance
– High AV
– Slim Design
– 5mm connectors
– Dimensions: 139mm(L)x37.3mm(W)x24.8mm(H)
– Weight: 238g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Speedzone 5200mAh 120C 2S 7.4V Lipo
Pack rated at continuous 120C. Standard 5mm connectors.
– High capacity for maximum duration
– 120C discharge rating
– 5mm connectors
– Dimensions: 138.5mm(L)x47mm(W)x24.75mm(H)
– Weight: 260g +/- 2g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
Evolution SC80 80A SPEC ESC
The SC80 electronic speed controller (ESC) is specifically designed for 1/10 scale SPEC class electric R/C racing and is suitable for both off-road and on-road classes. It comes factory set in “blinky” mode with the same setup of United States Stock TC ACE Dave Johnson. And although the factory default setting is an optimized setup for “blinky” mode, an optional program box is available to customize settings to suite driving styles in “blinky” mode as well as non-“blinky” mode. The controller is 2S LiPo compatible, has a 9.5T and above motor limit and comes with factory installed wires, capacitor and fan.
Specifications:
Continuous Current: 80A
Battery Input: 2S LiPo, 2S LiFe, 4-8 cells NiMh/NiCd
Built-in BEC: 6V@5A
Motor Limit: Over 9.5T
Motor Type: 540 size 2 pole sensored brushless
Size: 32mm(L) x 26mm(W) x 24mm(H – with fan)
Weight: 52g (with fan, wires and capacitor)
Evolution 6000mAh 130C 2S 7.4V LCG Lipo
High AV, Low IR. LCG Pack rated at continuous 130C. Standard 5mm connectors.
The low-profile design allows you to further fine tune the handling characteristics of your car.
– High capacity for maximum duration
– 130C discharge rating
– Low Resistance
– High AV
– Low Profile
– 5mm connectors
– Dimensions: 139mm(L)x47mm(W)x22.4mm(H)
– Weight: 294g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
– ROAR Approved
Evolution 5200mAh 130C 2S 7.4V Shorty Lipo
High AV, Low IR. Rated at continuous 130C. Standard 5mm connectors.
– High capacity for maximum duration
– 130C discharge rating
– Low Resistance
– High AV
– 5mm connectors
– Dimensions: 96mm(L)x47mm(W)x25mm(H)
– Weight: 228g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
– ROAR Approved
Evolution 8100mAh 130C 1S 3.7V Lipo
High AV, Low IR. Rated at continuous 130C. Standard 5mm connectors.
– High capacity for maximum duration
– 130C discharge rating
– Low Resistance
– High AV
– 5mm connectors
– Dimensions: 93mm(L)x47mm(W)x18.5mm(H)
– Weight: 160g
– Meets ROAR, EFRA, BRCA, and IFMAR specs
– ROAR Approved
